Front Brake Rotor - ACDelco (177-1050)
ACDelco - 1771050
- Sale Price: $143.24
Details
- Brand:
- SKU:
177-1050
- GTIN: 00707773641422
- UPC: 707773641422
- Positions: Front
- Other Names:
92245928
- Description: ACDelco GM Original Equipment Disc Brake Rotors are metal discs mounted to the wheel hub where the caliper can press the brake pads against the disc surfaces to slow the vehicle, and are GM-recommended replacements for your vehicle's original components. These disc brake rotors have been manufactured to fit your GM vehicle, providing the same performance, durability, and service life you expect from General Motors. ⚠ WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov
disc-brake-rotor;rotor;brake-rotor;disc-brake; - Condition: New
California Proposition 65
WARNING: Cancer and reproductive harm - www.P65Warnings.ca.gov - Sale Price: $143.24
Drop Ship
Direct Shipping From Supplier [*]
Some products available are shipped directly from the manufacturer or supplier rather than from our own warehouse. This allows us to offer you a wider selection of parts at competitive prices. When an item shows "Drop Ship" the supplier currently has it in stock and it will typically ship within 1–2 business daysAdditional Information
| Brand | GM Genuine Parts |
| ABS Tone Ring Included | No |
| Bearings Included | No |
| Bolt Circle Diameter (in) | 4.7 |
| Bolt Circle Diameter (mm) | 120 |
| Bolt Hole Quantity | 5 |
| Center Hole Diameter | 2.64 67 |
| Construction | Full Cast |
| Conventional Or Drum-In-Hat Type Rotor | Conventional |
| Directional or Non-Directional Brake Surface | Non-Directional |
| Disc Finish | Ground |
| Discard Thickness | 30 1.18 |
| Features & Benefits - Bullet 1 | Inspected for balance, resulting in smooth brake operation and noise reduction |
| Features & Benefits - Bullet 2 | GM-recommended replacement part for your GM vehicle's original factory component |
| Features & Benefits - Bullet 3 | Offering the quality, reliability, and durability of GM OE |
| Features & Benefits - Bullet 4 | Manufactured to GM OE specification for fit, form, and function |
| Good Maintenance Practices - Section 1 - Bullet 1 | Check brake fluid level at every oil change. Replace fluid according to owner's manual recommendations. |
| Good Maintenance Practices - Section 1 - Bullet 2 | Calipers and wheel cylinders should be checked every brake inspection and serviced or replaced as required. |
| Good Maintenance Practices - Section 1 - Bullet 3 | Inspect the brake lines for rust, punctures, or visible leaks (You may be able to do this, but consult a qualified technician if necessary). |
| Good Maintenance Practices - Section 1 - Bullet 4 | Check the thickness of your brake pads. |
| Good Maintenance Practices - Section 1 - Header | The following inspections and maintenance procedures can help prevent potential brake problems. |
| Good Maintenance Practices - Section 2 - Bullet 1 | Inspection of the brake hoses for brittleness or cracking. |
| Good Maintenance Practices - Section 2 - Bullet 2 | Inspection of brake lining and pads for wear or contamination by brake fluid or grease. |
| Good Maintenance Practices - Section 2 - Bullet 3 | Inspection of wheel bearings and grease seals. |
| Good Maintenance Practices - Section 2 - Bullet 4 | Parking brake adjustments (as needed). |
| Good Maintenance Practices - Section 2 - Header | The following should be conducted by a qualified technician: |
| Grade Type | Regular |
| Hat Finish | Coated |
| Height (in) | 2 |
| Height (mm) | 48.2 |
| Inside Diameter | 166 6.54 |
| Length (in) | 14 |
| Lug Quantity | 5 |
| Material | Cast Iron |
| Mounting Bolt Hole Circle Diameter | 4.3 109.25 |
| Nominal Thickness | 1.26 32 |
| Outside Diameter | 354.94 13.97 |
| Overall Height | 49.7 1.96 |
| Pad Contact Surface Width | 2.5 63.5 |
| Programming Required | No |
| Rust Resistant Coating | Yes |
| Signs of Wear & Troubleshooting - Section 1 - Bullet 1 | Vehicle pulls to the left or right when brakes are applied. |
| Signs of Wear & Troubleshooting - Section 1 - Bullet 2 | Visible ridges or deep grooves on the rotor surface. |
| Slotted | No |
| Solid Or Vented Type Rotor | Vented |
| Stud/Lug Hole Circle Diameter | 109.25 4.3 |
| Stud/Lug Hole Diameter | 16.25 0.64 |
| Stud/Lug Hole Quantity | 5 |
| Surface Type | Smooth |
| Weight (lb) | 25.6 |
| Width (in) | 14 |
Also Purchased
Also Purchased
Interchange
Policies
Vehicle Fitment
Select Your Vehicle Select
| Year | Make | Model | Body & Trim | Engine & Transmission |
|---|