Front and Rear Brake Pipe - ACDelco (84945002)
ACDelco - 84945002
- Sale Price: $60.66
Details
- Brand:
- SKU:
84945002
- GTIN: 00193468808803
- UPC: 193468808803
- Other Names:
84945002
- Description: ACDelco GM Original Equipment Brake Hydraulic Lines are quality reinforced lines that carry fluid within the brake system, and are GM-recommended replacements for your vehicle's original components. The hydraulic fluid must travel to the wheel brakes from the master cylinder. It does this through brake lines or pipes and brake hoses. Brake lines and hoses are designed to withstand high pressures, and these brake hydraulic lines have been manufactured to fit your GM vehicle, providing the same performance, durability, and service life you expect from General Motors. ⚠ WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov
- Condition: New
California Proposition 65
WARNING: Cancer and reproductive harm - www.P65Warnings.ca.gov - Sale Price: $60.66
Drop Ship
Direct Shipping From Supplier [*]
Some products available are shipped directly from the manufacturer or supplier rather than from our own warehouse. This allows us to offer you a wider selection of parts at competitive prices. When an item shows "Drop Ship" the supplier currently has it in stock and it will typically ship within 1–2 business daysAdditional Information
| Brand | GM Genuine Parts |
| Bendable | No |
| End 1 Flare Type | Inverted |
| End 2 Flare Type | Inverted |
| Features & Benefits - Bullet 1 | GM-recommended replacement part for your GM vehicle's original factory component |
| Features & Benefits - Bullet 2 | Offering the quality, reliability, and durability of GM OE |
| Features & Benefits - Bullet 3 | Manufactured with GM Original Equipment specification for fit, form, and function |
| Fitting Material | Steel |
| Fitting Type | Flare |
| Good Maintenance Practices - Section 1 - Bullet 1 | Check brake fluid level at every oil change. Replace fluid according to owner's manual recommendations. |
| Good Maintenance Practices - Section 1 - Bullet 2 | Calipers and wheel cylinders should be checked every brake inspection and serviced or replaced as required. |
| Good Maintenance Practices - Section 1 - Bullet 3 | Inspect the brake lines for rust, punctures, or visible leaks (You may be able to do this, but consult a qualified technician if necessary). |
| Good Maintenance Practices - Section 1 - Bullet 4 | Check the thickness of your brake pads. |
| Good Maintenance Practices - Section 1 - Header | The following inspections and maintenance procedures can help prevent potential brake problems. |
| Good Maintenance Practices - Section 2 - Bullet 1 | Inspection of the brake hoses for brittleness or cracking. |
| Good Maintenance Practices - Section 2 - Bullet 2 | Inspection of brake lining and pads for wear or contamination by brake fluid or grease. |
| Good Maintenance Practices - Section 2 - Bullet 3 | Inspection of wheel bearings and grease seals. |
| Good Maintenance Practices - Section 2 - Bullet 4 | Parking brake adjustments (as needed). |
| Good Maintenance Practices - Section 2 - Header | The following should be conducted by a qualified technician: |
| Height (in) | 3.85 |
| Inside Diameter | 4.95 0.19 |
| Length (in) | 9 |
| Line Length | 678.84 26.73 |
| Line Material | Steel Rubber |
| Outer Spring | No |
| Outer Wear Guard | Yes |
| Outside Diameter | 6.87 0.27 |
| PADB ID 3031 | 0.47 12 |
| PADB ID 951 | 0.47 12 |
| Pre-Formed | Yes |
| Signs of Wear & Troubleshooting - Section 1 - Bullet 1 | Brake pedal pulsation (not to be confused with normal ABS operation). |
| Signs of Wear & Troubleshooting - Section 1 - Bullet 2 | Vehicle pulls to the left or right when brakes are applied. |
| Weight (lb) | 1.3 |
| Width (in) | 7.25 |